30-Day Returns • Fast Dispatch • Free UPS Shipping

Categories
Chip Tuning Basics

What Is a Stage 1 Tune?

A stage 1 tune is a software calibration for a stock car — no new parts. What it changes, what you need, how much power it adds (dyno results) and what it costs.

A stage 1 tune is a calibration for a stock car. No new parts: the engine computer (ECU) is told to run the engine differently — more fuel where it can use it, adjusted ignition timing, and on turbo engines more boost. Everything else stays factory.

Below: what “stage 1” means, what you need, how much power it adds (with dyno results and where each comes from), what it costs, and how to get one without flashing your ECU.

What does stage 1 mean?

“Stages” are tuner shorthand, not an official standard. The usual meaning:

  • Stage 1 — software only, for a car with stock hardware.
  • Stage 2 — a calibration written for bolt-on parts: intake, exhaust or downpipe, often a bigger intercooler on turbo cars. What is a stage 2 tune? →
  • Stage 3 — major hardware: a bigger turbo, fuel system, sometimes internal engine work.

Because nothing physical changes, stage 1 is the only stage you can add to a daily driver and take back off. Side by side: stage 1 vs stage 2 →

What do you need for a stage 1 tune?

  • A stock engine in good health. Fix existing problems first: a check engine light, misfires, worn spark plugs. A tune doesn’t cure them.
  • The right fuel. Use the octane the tune is set for. With Monte you choose your fuel grade during setup.
  • A calibration for your exact engine and year. Not a universal “chip” — stage 1 means a calibration made for your engine.
  • About 120 miles of normal driving after installing, while the ECU adapts.

No parts, no lift, no shop. Check your car →

How much horsepower does a stage 1 tune add?

It depends most on whether the engine is turbocharged. A calibration can raise boost on a turbo engine; on a naturally aspirated engine it can only refine fuelling and timing. What Monte measured on a chassis dyno, before and after:

Car Engine Gain Source
Ford F-150 Raptor 3.5 EcoBoost +21 hp, +31 lb-ft Lab test, SEMA Garage, Diamond Bar, CA
Mercedes C300 2.0 turbo +25.1 hp, +72.2 lb-ft Dyno on video
Nissan 370Z 3.7 V6 +22.3 hp, +16.8 lb-ft Dynocom customer dyno report
Mazda MX-5 2.0 +16.6 hp, +17.1 lb-ft Dynocom customer dyno report

Monte adds up to 20% on a turbocharged engine and up to 12% on a naturally aspirated one. For your exact engine, the catalogue shows the factory rating and our estimate. How to read a dyno result →

How to stage 1 tune a car

There are two ways to get a stage 1 tune on a stock car:

  • Flash tune — the ECU’s stored software is rewritten with a new map, with a handheld programmer or at a shop. The largest gains; the change stays until you flash back.
  • Plug-in ECU tuner (Monte) — a device in the OBD-II port with a calibration for your engine. It adjusts fuelling and ignition timing, and boost on turbo engines, without rewriting the ECU’s stored software. Unplug it and the car is stock.

A custom flash can go further than a plug-in tuner; a plug-in tuner is stage 1 you can take off in seconds. Flash, handheld, piggyback and plug-in compared →

With Monte it takes about 5 minutes: plug it into the OBD-II port, follow the setup (tire size, fuel grade, mode), then drive normally for about 120 miles.

How much does a stage 1 tune cost?

A flash tune is priced by the tuner and the car, and a custom dyno session costs extra. Monte is a fixed price with free UPS shipping: Monte GT $279 (set up and switched in the Monte app) and Monte GTR $399 (its own touch screen, plus live gauges, error codes, a 0–60 timer and a virtual dyno). Both carry a 30-day return and a lifetime warranty on manufacturing defects.

Is a stage 1 tune bad for your engine?

A tune is only as good as its calibration. Before buying any tune, ask: is it written for your engine and year, does it keep the ECU’s factory protections such as knock control, and can you return to stock?

Monte’s calibration is written per engine and year, works with the factory ECU’s protections rather than switching them off, and comes out of the OBD-II port when you want the car back to stock.

Does Monte fit my car?

Monte covers cars and trucks with an OBD-II port — in the US from 1996. Find your make, model, engine and year in the catalogue: every page shows the factory rating and our estimate. Turbo diesels and pickups have their own pages: diesel tuner and truck tuner.

FAQ

What is a stage 1 tune? A calibration change on a stock car — fuel, ignition timing and, on turbo engines, boost — with no new parts.

What do I need for a stage 1 tune? A healthy stock engine, the fuel grade the tune is set for, and a calibration made for your engine and year.

How much hp does a stage 1 tune add? It depends on the engine. On our dyno tests Monte added 16.6–25.1 hp; it’s rated up to 20% on turbo engines and up to 12% on naturally aspirated ones.

Can I do a stage 1 tune myself? Yes. A handheld programmer flashes the ECU yourself; a plug-in tuner like Monte installs in about 5 minutes with no tools.

Is Monte a stage 1 tune? Yes — a plug-in stage 1 tuner for stock engines. Unplug it and the car is back to stock.